欢迎访问:济南赢彩数码科技有限公司官方网站
服务热线
187-6406-8302
当前位置:主页 > 公司动态 >

防止瓷砖打印机喷头损坏的方法

文章出处:www.wincolour.com 作者:colour 人气: 时间:2017-05-20 09:32 【
    瓷砖打印机喷头在正确的使用和保养下,8-12个月可以正常使用,如果不正确的操作就会大大降低喷头的使用寿命。经过长期的经验积累,济南赢彩技术部总结防止瓷砖打印机喷头损坏的方法,告诉客户注意日常维护。
Tile printer nozzle in the correct use and maintenance, 8-12 months can be used normally, if not correct operation will greatly reduce the nozzle life. After a long experience accumulated, Jinan win color technology department summary to prevent damage to the tiles printer nozzle, to tell customers attention to routine maintenance.
 
@1、在没有断电的情况下 ,随时安装拆卸瓷砖打印机的电路。这种行为会损害各个系统的使用寿命,危害喷头。
@ 1, in the absence of power failure, at any time to install the circuit to remove the tiled printer. This behavior can damage the life of each system, endanger the nozzle.
 
@2、随意加注不同批次的墨水,或使用质量不过关的墨水或者清洗液。两种不同配置的墨水混杂会改变墨水色彩和品质,质量不过关的墨水会影响喷绘效果和堵塞喷头,质量不过关的清洗液可能会腐蚀喷头。
@ 2, free to add different batches of ink, or the use of quality, but the ink or cleaning fluid. Two different configurations of ink mixing will change the ink color and quality, but the quality of the ink will affect the inkjet effect and plug the nozzle, but the quality of the cleaning solution may corrode the nozzle.
 
@3、对喷头进行高压气枪大力清洗。喷头如果被轻微堵塞,建议使用吸尘器将灰尘洗出,再进行细致清洗,不要用这种方式。
@ 3, the nozzle for high-pressure air gun vigorously clean. If the nozzle is slightly blocked, it is recommended to use a vacuum cleaner to wash out the dust, and then fine cleaning, do not use this way.
 
@4、将喷头整个放入清洗液中浸泡。清洗液具有一定腐蚀性,一般只取适量导入喷头中进行清洗。
@ 4, the nozzle will be soaked into the cleaning solution. Cleaning fluid has a certain corrosive, generally only take the right amount of the nozzle for cleaning.
 
@5、将清洗液留在喷头中超过48小时。清洗液长时间浸泡可更有效清除污渍,但是,如果时间超过48小时,会对喷头喷孔造成影响。
@ 5, the cleaning solution to stay in the nozzle for more than 48 hours. Cleaning the solution for a long time soak can be more effective to remove stains, but if the time is more than 48 hours, the nozzle nozzle will be affected.
   
@6、用自备无质检产品清洁喷头。喷头十分容易被污染和磨损,所以请使用瓷砖打印机厂家指定产品和质检过关产品清洁喷头。
@ 6, with their own quality control products clean nozzle. The nozzle is very easy to be contaminated and worn, so please use the tiles printer manufacturers designated products and quality inspection clearance products cleaning nozzle.
 
@7、使用外力不规范调整喷头位置。无论是更换还是微调喷头,都不要使用蛮力,请按照规范谨慎对待喷头。
@ 7, the use of external force is not standardized to adjust the nozzle position. Whether it is to replace or fine-tune the nozzle, do not use brute force, please follow the norms carefully treat the nozzle.
 
@8、清洗时不注意保护电路板和其他内部系统。清洗时请关闭电源,并且注意不要让水碰到电路板和其他内部系统。
@ 8, cleaning does not pay attention to protect the circuit board and other internal systems. Turn off the power when cleaning, and be careful not to touch the circuit board and other internal systems.
 
@9、长时间使用超声波清洗机清洁喷头。其实,如果平时注意瓷砖打印机喷头保养的话,根本无需进行超声波清洗。超声波会对喷头造成不良影响。但是如果堵塞严重,需要使用超声波清洗的话,一次清洗时间最多为3分钟。如果一次没有清洗感觉,请等待喷头自然降温至正常状态后再进行第二次清洗。
@ 9, long time using ultrasonic cleaning machine cleaning nozzle. In fact, if you usually pay attention to the maintenance of ceramic tile nozzle, then no need for ultrasonic cleaning. Ultrasound can cause undesirable effects on the nozzle. But if the blockage is serious, need to use ultrasonic cleaning, then a cleaning time up to 3 minutes. If there is no cleaning feeling, please wait for the nozzle to cool down to the normal state after the second cleaning.

在线客服

扫码与我交流