欢迎访问:济南赢彩数码科技有限公司官方网站
服务热线
187-6406-8302
当前位置:主页 > 行业动态 >

使用瓷砖打印机的方法是什么?

文章出处:www.wincolour.com 作者:colour 人气: 时间:2017-05-19 09:15 【
使用瓷砖打印机www.wincolour.com的方法是什么呢?今天济南赢彩小编就为大家介绍下瓷砖打印机在使用的时候需要注意以下六点方法。
What is the method of using the tile printer www.wincolour.com? Today, Jinan win color Xiaobian to introduce the next tile printer in the use of the time need to pay attention to the following six methods.
 
第一、当瓷砖打印机要换位置的时候,不能抬着打印机平台来搬动,而是在机器底部,扣住机壳部位来调换位置。
First, when the tile printer to change the position, can not lift the printer platform to move, but at the bottom of the machine, buckle the chassis parts to swap position.
 
第二、大多数人在初次使用设备的时候,都会觉得USB的接口线不好插,此时需要通电再下降一点很容易就连接上。
Second, most people in the initial use of equipment, will feel that the USB interface line is not easy to plug, then need to power and then drop a little easier to connect.
 
第三、给瓷砖打印机 加墨水的方式。一般就是2种供墨方式,@1独立墨盒,@2连续供墨系统,这两种供墨系统都有一整套部件组成,墨盒,喷头,清洁单元,导墨管,废墨瓶。遇到在加墨或者墨管不通的情况下,可以使用注射器在墨盒底端抽气,直到有墨水进入注射器里面。或者在废墨瓶口上的导墨管抽墨水也可以。
Third, the way to add ink to the tiled printer. In general, there are two kinds of ink supply, @ 1 independent ink cartridges, @ 2 continuous ink supply system, these two ink system has a complete set of components, ink cartridges, nozzles, cleaning units, ink tube, waste ink bottles. In the case of refueling or ink management, you can use the syringe to pump the bottom of the cartridge until there is ink into the syringe. Or in the waste ink bottle on the ink tube can also be ink.
 
第四、要消除静电非常的简单,只要在金属表壳接出一根外接电线,把外接电线接地即可。
Fourth, to eliminate static electricity is very simple, as long as the metal case to take out an external wire, the external wire can be grounded
 
第五、当喷头出现滴墨情况,一种是清洁单元的橡胶圈密封松脱或者损坏,此时需要更换橡胶密封圈。另一种是喷头被撞后有墨滴聚集在喷头底部,此时需要使用棉球在喷头底部擦拭下就好了。
Fifth, when the nozzle appears drop ink situation, one is the cleaning unit of the rubber ring seal loose or damaged, then need to replace the rubber seal. The other is the nozzle was hit after the ink droplets gathered in the bottom of the nozzle, this time need to use the cotton ball in the bottom of the nozzle to wipe under the like.
 
第六、瓷砖打印机高度的调整。现在的UV打印机主要以红外线检测物体高度,物体放置好后再打印。如果打印物品表面有凹凸现象,一定要记住调整喷头和打印产品的高度,以免撞坏喷头。
Sixth, the height adjustment of the tile printer. Now the UV printer mainly to infrared detection of object height, the object is placed and then print. If the surface of the printed items have bumps, be sure to remember to adjust the height of the nozzle and print products, so as not to damage the nozzle.
 
以上六点就是济南赢彩小编为大家提供的瓷砖打印机的使用方法,希望能对大家有帮助。
Above six points is Jinan win color Xiaobian for everyone to provide the use of tile printer, hoping to help everyone.

在线客服

扫码与我交流